Body Shop [Archive] - Page 63 - Team Camaro Tech

: Body Shop



  1. rust
  2. IMPORTANT question about wet sanding before paint
  3. front & rear molding clips
  4. black vinyl top to go with black 'stinger' hood?
  5. media blasting question
  6. Goodmark or Dynacorn
  7. back in the trunk!
  8. Toeboards Finished in '68
  9. Left rear quarter window and window felt question
  10. Under coatings?
  11. Rottisserie hook up
  12. how much gap do you have? Fender to firewall.
  13. 68fan is your camaro bolero red
  14. Were Butternuts painted over???
  15. trunk lid tweaking ?
  16. What will this restore run me?
  17. Jambing
  18. Fire wall smoothing existing ribs???
  19. Urethane primer v.s. epoxy primer
  20. Need Sub-frame to body mounts (Not solid)
  21. Door Striker/Bushings
  22. What to use to remove paint from grill?
  23. Removal of windshield trim
  24. stripes over a stinger hood
  25. Oh yea; First coats of color on parts!!!!!!
  26. 1969 Camaro Rain Drip Rail Trim ...
  27. color change now? or later? front end is off.pics
  28. Pictures of new paint job
  29. Under Panel Color
  30. Happy Father's Day to all Camaro Dads!
  31. in for restoration,finally
  32. Fiberglass question
  33. Inner fender install
  34. Body Filler Help
  35. Removing rear frame rails on a 68?
  36. Trunk from 67-68 Camaro will fit a 69?
  37. Wheel well mouldings
  38. Rear Deck Spoiler....too far back?
  39. Paint Application Procedure
  40. repaint question
  41. Trunk pan different in coupe vs vert?
  42. in for restoration,finally
  43. Paint codes for Hugger Orange and Tuxedo Black
  44. How do you remove convertible frame?
  45. Repro Front Fenders
  46. Devilbliss startingline....anygood..???
  47. GM hood Identification
  48. Are there rules for striping?
  49. Brake on a door skin
  50. Wet sanding clearcoat.
  51. Dynacorn Parts (No Bashing I promise)
  52. Door Jamb loom hole location
  53. Rear inner fender work
  54. rear wheel rub
  55. ZL2 Hood Question
  56. 67/68 tail light panel identification
  57. need help with standard to rs fender brackets
  58. Inner Rocker / Cowl / kick panel area pics?
  59. Paint on Rims
  60. 67/68 Deck Lid With Spoiler
  61. How far away from under surface for spraying?
  62. What happened with the metal??
  63. Rusted bolts on subframe
  64. PIC NEEDED please... Inner cowl w/air cond.
  65. starting to take my 67 apart
  66. Paint Type and Color - Rear Axle, Leaf Springs, Frame
  67. New to paint, replacement for unavail DP90? And seam seal question.
  68. can't remove water stains on front bumper
  69. Front airdam
  70. Who Does Sub Frame Restorations in Vancouver
  71. after 6 years time to prime
  72. Sandblaster brand / model
  73. what was the purpose of "PBT" on the firewall
  74. Another 68 With a Heartbeat!
  75. best repro grille
  76. Get the AIR Dry
  77. OVERSPRAY! question....
  78. Rs Headlight adjustments
  79. front fenders
  80. off to my buddys body shop
  81. Mismatch paint on upper cowl vent/grille
  82. Emblem question
  83. Tail Light Trim
  84. 1968 SS/RS Convertible Paint Color Team Vote
  85. FRESH paint on my 68; done at home in GARAGE!
  86. Media Blast material for undercarriage
  87. door dent repair
  88. Canada Day
  89. 68 LH NOS full quarter panel
  90. 67 upper dash replacement planning
  91. Fresh Out of Jail, And It's California Dreamin! - LOTS OF PAINT PICS!!
  92. Need advice >
  93. Z/28 rally stripe decal kits
  94. Rear spoiler install
  95. Painting with Convertible Top in place
  96. Non-Camaro Violence has occured!
  97. Thinking of getting rid of the front bumper on my 68 rs
  98. Leaking Windows
  99. ermine white, dash
  100. need help
  101. Epoxy to metal or metal to metal?
  102. Window seal channel to body
  103. Any good place to send trim for a refresh?
  104. Firewall and cowl interchangeable coupe/convertible?
  105. D90 Stripes from Phoenix Graphix
  106. Slick sand
  107. "Basics of Basics" Door moisture shields
  108. 68 Frame-on Restoration
  109. who has dealer emblems on there car
  110. Vin Tag (unbelievable story)!!
  111. Door glass stabilizer strip question
  112. smoothing firewall progress...pics
  113. Hardener for Acrylic Enamel
  114. Hugger Orange Touchup paint
  115. Current Repro Endura bumpers for 69?
  116. Original68, car; painted, cut and buffed......
  117. Rolling fenders
  118. Cleaning and re-doing window regulators
  119. underbody?
  120. how much body work did you have to do to your goodmark cowl hood
  121. Is a binks 2001 a good paint gun??
  122. What to do with seem from quarter skin? photo
  123. VOTE ON.... Rear Endura Bumper
  124. "Oil Can" Dent
  125. Need pics of different greens
  126. Old paint, new paint $ prices ?
  127. Block out and metal glaze on paint
  128. Replacing trunk assy
  129. Opinions wanted: '69 Glacier blue with White or Black Z28 stripes?
  130. And away she goes
  131. Hood Profile Doesn't Match Fender
  132. Need a good Welding Kit
  133. Hoods
  134. Dessicant Dryer Homemade
  135. Polishing options for original fuel tank
  136. Pics of 80% Quarters
  137. How much to weld these seat brackets in?
  138. making a '67 valance fit
  139. Replacing Fenders - 1 at a time ('67)
  140. rocker molding on 69
  141. Will primer (with no topcoat) prevent rust on a driven vehicle?
  142. Powder Coating Genius!!! If you are looking for someone.
  143. Replacing lower door roller Detant pin
  144. one owner 69 coupe ground up update for motivation
  145. Eastwoods, Crowit Cold Galvanizing Compoud as a weld through?
  146. Sandblasting/Painting Parts....
  147. Front edge of door rubs, shim or trim?
  148. 1969 grill on a 1967 camaro
  149. Glass hood guys
  150. Paint on plastic won't cure
  151. replacement fender?
  152. 67 camaro spoiler
  153. Windscreen moldings
  154. Tail Light Housing Refinishing
  155. welding troubleshooting
  156. Any difference in 67 an 68 80% quarters?
  157. How soon to "wax" after paint?
  158. 68 Drip rail replacement
  159. Anyone in Washington State near Blaine I can ship parts to?
  160. repro '68 bumper, any luck?
  161. door skin seams, seal or not and how?
  162. 60% Gloss Black Paint
  163. PLEASE HELP! - Black top by freklers?
  164. Rust on sheetmetal
  165. Gas Tank - plug???
  166. Can you help me with the chrome trim installation?
  167. Idea's/Opinions needed to liven up Lemans Blue
  168. 68 repro front sheet metal stamped off original GM tooling - WORTH IT?
  169. Torque Specs
  170. primer touch-up question
  171. Rock Auto Gas Tank - Shipping Question...
  172. PPG Experts, K36 Primer,..body work on top?
  173. Wiper Motor Cover
  174. front valance
  175. "Basics of Basics" Wheel stands vs Jack stands.
  176. Damaged rear end
  177. Looking for good car cover
  178. Fender Shims - What's normal if anything?
  179. great site for all First Gen colors
  180. engine bay decals
  181. Look what galloped up to my all F body stable today
  182. How to brace it up?
  183. Rear filler panel-Different question
  184. WOW, am i ever ticked off!
  185. front clip assembly sequence
  186. Binks siphon conversion
  187. Gas Cup...
  188. 69 camaro roof skin
  189. hood scoop
  190. Tilt front end
  191. '68 Camaro Restoration Project For Dad!
  192. 67 Camaro project
  193. House of kolor
  194. Does a car need to be on its wheels to do full quarters and roof.
  195. Sandpaper roughness
  196. Looking for a good anti rust/Battery corrosion
  197. 67 Detent Roller repair with out removing door?
  198. striping question
  199. Quick question on adjusting a 67' door
  200. glass-to-sash channel bushing
  201. Is this the firewall dimple for throttle cable?
  202. rear quarter glass
  203. Body filler in a gun, anyone using it?
  204. My Restification of a '67 Cpe
  205. How long can Nason etch primer sit?
  206. It's coming home friday
  207. fender to cowl spacing
  208. NOS and aftermarket
  209. 1967 Yenco Hood
  210. Open can life for PPG DPLF and Self Etch?
  211. new paint on my 67
  212. Convertible Outer Rocker Metal Thickness?
  213. Rear Window Haze New Glass
  214. Grinding floor seam
  215. Waves/ripples in trunk pan
  216. Trunk Pan Install
  217. Rear 1/4 window help
  218. Drip rails
  219. Trunk lid tension rods (springs)
  220. refinishing satin finish molding/brackets
  221. Seat foam.
  222. Quarters Tailpan and Deck filler welded as subassembly.
  223. Roof and Quarters question
  224. Trunk lid
  225. 69 inside door color
  226. EMERGENCY...Paint guys...help/question
  227. Midwest body shop anywhere?
  228. painted and cleared today
  229. Rear window molding clips
  230. Gas Tank Insulator
  231. Trunk Weatherstrip
  232. Windshield removal
  233. engine decals
  234. Need help please read...
  235. bubbles in my paint job
  236. 80% quarter cut location
  237. Shopline primer surfacer question
  238. 69 front fenders
  239. Glasruit paint
  240. trunk lid to 1/4 panel gap
  241. need confirmation - 68 front spoiler(s)
  242. My Chrome is Home.....Bumpers that is...
  243. My 69 resto started finally!!
  244. First timer restoration, 67 RS
  245. paint protection, Need help!
  246. Passenger side rear upper shock tower?
  247. Question on door jamb vents
  248. endura bumper
  249. Best Wax to Use on New Paint
  250. Question on show panel