|
KevinW Mar 29th, 09, 06:40 PM I have been testing dash top paint looking for a good one. I found Kyron Ultra-flat black Camo paint and did the dash top today. 2 coats, looks great! More flat then flat and no gloss! http://www.fototime.com/17DCAF5086A9C17/standard.jpg TraxUnderground Mar 29th, 09, 07:07 PM Sounds great Kev...waiting for pics... zbo2 Mar 29th, 09, 07:55 PM yea.........how 'bout us guys with non black dashes.....JK......i used low gloss laquer for most of the interior metal. can't wait to see how the plastic stuff comes out though. parkbrau Mar 29th, 09, 11:23 PM I have been testing dash top paint looking for a good one. I found Kyron Ultra-flat black Camo paint and did the dash top today. 2 coats, looks great! More flat then flat and no gloss! http://www.fototime.com/17DCAF5086A9C17/standard.jpg Thanks, We have that same Paint in the BX here. I was thinking about buying that Paint, especially after the paint I have on it now just flaked on me, partly because the dash wobbled a little when I did a test fitment. Anyway, how did you fasten the dash down? That is a dash top replacement panel right? I dont see any spot welds. KevinW Mar 30th, 09, 05:22 AM yea.........how 'bout us guys with non black dashes.....JK......i used low gloss laquer for most of the interior metal. can't wait to see how the plastic stuff comes out though. The Camo comes in green/brown too :D John, the dash panel was mostly glued with panel epoxy and mig-ed around the inside and sides. Myfirst 69SS Mar 30th, 09, 05:28 AM The Camo comes in green/brown too :D John, the dash panel was mostly glued with panel epoxy and mig-ed around the inside and sides. Kevin, I just bonded my upper panel yesterday. What did you use? I used Lord Fusor and it was not fully cured after 6 hours because of the tempature. Did you spray that flat black right over the e-coat on the dash top or did you prime first? Looks great.. jcdubs Mar 30th, 09, 05:29 AM Lookin good Kevin, Will she be ready for Jackson this year? parkbrau Mar 30th, 09, 07:42 AM The Camo comes in green/brown too :D John, the dash panel was mostly glued with panel epoxy and mig-ed around the inside and sides. What Co. did you buy the panel epoxy from? I have read a few posts regarding it. Do you know if it can be used over a material such as PORE 15 or similar rust encapsulator? KevinW Mar 30th, 09, 10:35 AM Kevin, I just bonded my upper panel yesterday. What did you use? I used Lord Fusor and it was not fully cured after 6 hours because of the tempature. Did you spray that flat black right over the e-coat on the dash top or did you prime first? Looks great.. My freind did the body and paint, not sure what he used. I did borrow the panel adhesive for some other work and my garage was below 50 deg and did not cure well (failed really after 24 plus hours cure). I think you have to be above 70 deg. He epoxy primed the dash first and I painted over that. Lookin good Kevin, Will she be ready for Jackson this year? John, it should be ready, not sure it it will be May or Sept :) What Co. did you buy the panel epoxy from? I have read a few posts regarding it. Do you know if it can be used over a material such as PORE 15 or similar rust encapsulator? I bought the Camo at Ace hardware. It is regular enamel paint, if POR can be topcoated by enamel, then it should work. msicks Jul 12th, 11, 06:41 PM I'm getting ready to paint my dash with the camo paint just wondering how has it held up and does it scratch? Did you sand between coats what did you sand it with? THANKS | ||