Hi guys. I usually find what I'm looking for via the old posts and threads but no luck this time. Fortunate or not I've just bought a rear folding seat for my 67 SS/RS with deluxe interior and plan on doing the conversion from the non folding counterpart. Is there any good pics of the required brackets, latches, divider panel etc. that would put me on the fast track for everything that I need, and where they get mounted? I also need the bottom seat to complete the transformation (I bought my car with no back seat) and after reading several posts, I believe what I'm looking for a 67-69 bottom seat that was either deluxe, or came from a convertible. Right?
I love this website! Thanks, Real SS

The bottom seat can be either a 67 deluxe seat, or any 67-69 convertible(standard or deluxe) or fold down bottom(standard or deluxe). These all would be the narrow seat bottom you need. 68-69 deluxe seats were not narrow(unless vert or folddown), only 67.

Here is a pic I sent in a previous thread of the clip that holds the seat in the up position. It is held on with two screws. One on each side clips over the metal tab on the seat back to hold it in place.
http://www.camaros.net/showroom/data/500/Backseatcloseclip.jpg

Just an addition to Chris note. 67-69 Firebird seats will work too (and might be cheaper!). A deluxe interior in a Firebird was a short seat (with arm rests) like the converts.

Being a Firebird guy with a fold-down seat I can tell you that there were far more Firebirds produced with short seats than Camaros so Kevin is probably right. The rubber bumper is missing from the above photo and it should be noted that unlike other years, the '67 had the latches above on both sides. Those latches and the bumpers are available via reproductions as are the divider, divider gutter and mounting brackets. You should be good to go once you find a short bottom.

Heres a bunch that will fit. 48 inches wide is what you need.

http://cgi.ebay.com/ebaymotors/67-68-69-Firebird-Camaro-rear-seat-bottom-Original-GM_W0QQitemZ4639669580QQcategoryZ10076QQrdZ1QQcmdZ ViewItem

http://cgi.ebay.com/ebaymotors/1969-Pontiac-Firebird-Camaro-Rear-Seat-Bottom_W0QQitemZ110000043503QQcategoryZ33701QQrdZ1 QQcmdZViewItem

http://cgi.ebay.com/ebaymotors/1967-1968-camaro-firebird-bucket-seat_W0QQitemZ4640653171QQcategoryZ34206QQrdZ1QQcm dZViewItem

Email the seller about the size of this one

http://cgi.ebay.com/ebaymotors/67-69-Firebird-Camaro-rear-seat-bottom_W0QQitemZ8065625570QQcategoryZ33701QQrdZ1QQ cmdZViewItem

Heres is one that wont fit (see the cutouts for the rear wheel wells) for comparison.

http://cgi.ebay.com/ebaymotors/67-68-1967-1968-CAMARO-FIREBIRD-REAR-LOWER-SEAT-NICE_W0QQitemZ8065898293QQcategoryZ33701QQrdZ1QQcm dZViewItem

Hammered - My car did not have the bumpers on it. Do they attached to the seat latch with the inside sheet metal screw missing on the latch in my photo?

My car did not have the bumpers on it. Do they attached to the seat latch with the inside sheet metal screw missing on the latch in my photo?The bumpers install over the spring latch which also secures a plastic cover.

http://geocities.com/sdampier@sbcglobal.net/Team_Camaro/Folddown.jpg

Thanks Steve. That's what I needed.

Thanks for all of your help. Once again the fine members from T.C. come to the rescue.
Real SS

Just like Steve's photo.

Does anyone sell repro plastic covers (escutcheon) for the seat back latch?