Intake manifold for a 396 camaro - Team Camaro Tech
Tech 2000 Our previous General Forum
Replies ONLY - no new topics.

 
LinkBack Thread Tools Display Modes
post #1 of 5 (permalink) Old Jul 28th, 00, 04:56 PM Thread Starter
Tech Team
 
Join Date: Jul 2000
Location: St. Peters, MO. USA
Posts: 33
Question

I have a 67 ss/rs 396 camaro. The intake is a eldebrock torker II and the carb is a holley 750 double pumper. The problem is that there isn't much clearance, the filter is a 14 X 4 K&N and the base is the drop base. With everyting together there is about 5/8" between the choke horn and the air cleaner lid. And the air cleaner is about 1/2" from the hood. The hood by the way is the big block style hood with the grills. Does anyone have a good suggestion on a carb and intake set-up that would clear up some room. Some day a guy might want to throw juice at it.
Thanks
Mike
treyman is offline  
Sponsored Links
Advertisement
 
post #2 of 5 (permalink) Old Jul 28th, 00, 05:55 PM
Senior Tech
 
Join Date: Dec 1999
Posts: 1,515
Post

The torker II is probably the shortest manifold you can get, from where the intake mounts to the block to carb base plate the torker II is 4.60" , performer 5.4" and the performer RPM is 6.0" so you can't go any lower there. As for the carb an edelbrock would give you more clearance since they don't have the vent tube. Or get a cowl hood.

------------------
68 468 700R4, and here it is;
mutert23
MarkM is offline  
post #3 of 5 (permalink) Old Jul 29th, 00, 12:29 AM
Senior Tech
Bruce
 
Join Date: Jan 2000
Location: PA
Posts: 915
Post

i don't know if this will help seeing that you have a ss hood, but i run a weiand x-celerator intake on my big block with a 780cfm carb and i have a moroso air cleaner, 14x4, but i also have a stock cowl hood and i have enough room. i know hte filter is expensive, but can you go down to a 3" and if you need the air, what about a K&N stub stack? i never used one, but i know some that did and they really liked them.
bruce
bruce69camaro is offline  
 
post #4 of 5 (permalink) Old Jul 31st, 00, 05:12 PM
Gold Lifetime Member
Jim
 
Join Date: Dec 1999
Location: Yorkville, Illinois USA
Posts: 22,121
Post

Hmmm, if it was originally a small block car, and whoever put the rat in it didn't change the frame mounts, then the motor is sitting an inch higher than it should be.



JimM is offline  
post #5 of 5 (permalink) Old Aug 2nd, 00, 12:59 AM
Senior Tech
Johnny
 
Join Date: Dec 1999
Location: Rutledge, Tn.
Posts: 610
Question

Hey I have the same promblem & I used the big block frame mounts! I am at this time using a 3 " air filter in a drop base housing. I am using a stock cast iron Holley intake & a Eldebrock Carb.

------------------
johnny
johnnyr is offline  
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Team Camaro Tech forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address.
NOTE we receive a lot of registrations with bad email addresses. IF you do not receive your confirmation email you will not be able to post. contact support and we will try and help.
Be sure you enter a valid email address and check your spam folder as well.



Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may not post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome