87iroc 5.0 to 5.7 swap - Team Camaro Tech
Troubleshooting Diagnosing problems done here.

 
LinkBack Thread Tools Display Modes
post #1 of 5 (permalink) Old Aug 3rd, 99, 04:32 PM Thread Starter
 
Join Date: Aug 1999
Location: richmond va
Posts: 3
i recently installed a 5.7tpi in my 87 iroc. it had the 5.0tpi from the factory i swaped all existing components. i now have a lean idle condition and repeated stall in closed loop operation. my qwestion is. does anyone know if the components are compateable (injectors etc,) please respond or direct me to someone who can. all my thanks JIM
jims87iroc is offline  
Sponsored Links
Advertisement
 
post #2 of 5 (permalink) Old Aug 3rd, 99, 06:46 PM
Senior Tech
 
Join Date: Aug 1998
Location: Ft Wayne In.
Posts: 305
How do you know the idle is lean? did you have it on a scanner? Did you use the TPI and fuel rails from the 305? Did you use a 350 chip? Does it idle fast or slow? Does the IAC motor try to control the idle?
In closed loop the mixture is computed from the input of the sensors. In open loop it's ran by a set paramiter of info.
Give me some more info and I'll try to help you out!
Dave
Dave Birdwell is offline  
post #3 of 5 (permalink) Old Aug 4th, 99, 02:57 AM
 
Join Date: Jun 1999
Posts: 460
If you used the original 305 injectors then there's your answer. The TPI's are the same but the injectors are different between the 305 and 350.
68SS396 is offline  
 
post #4 of 5 (permalink) Old Aug 4th, 99, 05:32 PM Thread Starter
 
Join Date: Aug 1999
Location: richmond va
Posts: 3
this reply is for dave birdwell. i used the 305 fuel rail and injectors. i checked block learn at idle with a scan tool it read consitantly high about 140. i also set tps and min idle to spec. it has a new o2 senser and no vac leaks,timing is right. i also checked part #s for injectors that year 305 & 350 injectors are not the same, could this be the cause. thanks for your help. JIM
jims87iroc is offline  
post #5 of 5 (permalink) Old Aug 5th, 99, 05:32 AM
Senior Tech
 
Join Date: Nov 1998
Location: ohio
Posts: 252
You can sometimes help this with an adjustable fuel pressure regulator. Increase the pressure some and see what happens. When idling roughly, might just try unhooking the vacuum line to the present regulator which will give some increase. Also, does this 350 have a computer compatible camshaft. Excess duration and overlap may cause problems. tom
tom3 is offline  
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Team Camaro Tech forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address.
NOTE we receive a lot of registrations with bad email addresses. IF you do not receive your confirmation email you will not be able to post. contact support and we will try and help.
Be sure you enter a valid email address and check your spam folder as well.



Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome