BB solid lift cam valve lash - Team Camaro Tech
Engine General Engine Discussion.

 
LinkBack Thread Tools Display Modes
post #1 of 6 (permalink) Old Oct 12th, 02, 07:15 PM Thread Starter
Senior Tech
 
Join Date: Jul 2001
Location: Toney, AL United States
Posts: 166
I'm putting in a solid lift cam in a 427 but I seen no mention of the valve lash in with the cam. I was wondering what they should set at. The cam is an advertised 590 lift 294 duration. Thanks in advance for any help.
Bedanobub is offline  
Sponsored Links
Advertisement
 
post #2 of 6 (permalink) Old Oct 13th, 02, 04:57 AM
 
Join Date: Apr 2000
Posts: 21,341
Is the cam a CC 294S solid?? If it is, call them up and ask them or look in one of their cats. and find out.. pdq67

PS., a good starting point would be .022" intake/.024" exhaust.

I think the CC Magnum solids can be lashed OK from .015" to .030".



pdq67 is offline  
post #3 of 6 (permalink) Old Oct 13th, 02, 12:29 PM
Team Member
John
 
JohnZ's Avatar
 
Join Date: Sep 2000
Location: Washington, Michigan USA
Posts: 7,728
The lash specs should be on the cam card - never saw one without them.

------------------
JohnZ
CRG
'69 Z28 Fathom Green
JohnZ is offline  
 
post #4 of 6 (permalink) Old Oct 13th, 02, 01:27 PM Thread Starter
Senior Tech
 
Join Date: Jul 2001
Location: Toney, AL United States
Posts: 166
I purchased it from Flatlander racing. They had a section where you could list all the info on your engine, car weight, rear gear ratio, etc and come up with the best cam for the application. I found out by using this, they charged you $30 If you didn't decide to purchase the cam from them. This is keep all the people who just wanted a size and then purchase a cam elsewhere from bothering them..I guess. They told me they custom grind their cams and it would take 7 to 10 days. After they told me the size I was thinking man thats the same size as a comp cam I saw in a catalog. Rather than lose my $30 I bought one from them. Three weeks later I got it. The price was as high or higher than a comp or crane. I then find out that they don't grind their own it was a Schnider Racing cam and they had it drop shipped from their shop. Anyone ever used one of those brands? I looked over the cam card and I don't see anywhere what the lash is. The only thing I see is where it tells you to check piston to valve clearance by setting it at .000 lash but I don't see any other settings. I guess I can contact Flatlander again but they were starting to be a$$holes toward the end when I complained about a 7 to 10 day wait turning into a 21 day wait for a cam that I could have purchased the same day at the local speed shop.
Bedanobub is offline  
post #5 of 6 (permalink) Old Oct 13th, 02, 04:41 PM
 
Join Date: Apr 2000
Posts: 21,341
Please bear with it b/c it happened to me one time when S&H turned out to be almost 30 percent of my small order... Never went back to the place...pdq67



pdq67 is offline  
post #6 of 6 (permalink) Old Oct 13th, 02, 04:54 PM
Senior Tech
 
Join Date: Nov 2001
Location: Oxford Pa.
Posts: 503
Here's the link to Schnider's camshafts: http://www.schneidercams.com/shop.htm
I'm thinking they sent Ya a hydrauilc cam since there is no lash settings on the camcard...goto the link and checkout Your cam number...
18436527 is offline  
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Team Camaro Tech forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address.
NOTE we receive a lot of registrations with bad email addresses. IF you do not receive your confirmation email you will not be able to post. contact support and we will try and help.
Be sure you enter a valid email address and check your spam folder as well.



Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome