Streetdampr - Paint this??? - Team Camaro Tech
Tech 2002 General Tech questions from 2002
Replies ONLY, no new topics.

 
LinkBack Thread Tools Display Modes
post #1 of 5 (permalink) Old Aug 2nd, 02, 05:49 AM Thread Starter
Senior Tech
 
Join Date: Oct 2000
Location: CT
Posts: 389
I just got a Streetdampr. It's made of steel and says it's paintable.

Dumb Question:
-------------
If I don't paint it, will it rust? It is steel. If I do paint it I'd want to use the POR engine kit. That means Marine Clean and Metal Ready first.

Is it ok to use these products on the dampr???

Thanks,
Rob



[This message has been edited by RFrenette (edited 08-02-2002).]
RFrenette is offline  
Sponsored Links
Advertisement
 
post #2 of 5 (permalink) Old Aug 2nd, 02, 06:08 AM
Senior Tech
Mike
 
Join Date: Jan 2001
Location: GARDEN GROVE CALIF
Posts: 446
RF,it is going to rust if its not protected. I assume this balancer is also degreed. Use POR if thats your deal, mask the snout and the inner surface that slides over the crank. Then take a small brush and paint the degree lines after the POR dries. Should be cool.

------------------
Black 69 camaro
HOTROD69CAMARO is offline  
post #3 of 5 (permalink) Old Aug 2nd, 02, 06:59 AM
Gold Lifetime Member
Rick
 
Join Date: Feb 2000
Location: Accord, NY
Posts: 4,815
Bob, the engine paint requires heat to cure. I was going to do my bellhousing with the chevy orange but was told it won't fully cure.

------------------
Rick Dorion
69 RS Conv,355,M20,4.10's and I don't worry about stone chips ( yet ).
RickD is offline  
 
post #4 of 5 (permalink) Old Aug 2nd, 02, 07:38 AM
Senior Tech
 
Join Date: Aug 2001
Location: Atco Raceway
Posts: 2,069
Send a message via AIM to CamaroNOTcamero
Rob it wont cure. I dont know if you remeber the rear end cover i told you i painted. Well i took a chisel and make a small slice, put my finger underneath, and pulled all the "paint" (i wont consider it paint) off with my fingers. It should cure on the engine, but find something else else for the balancer.
I used Duplicolor from dupont and it worked great.
CamaroNOTcamero is offline  
post #5 of 5 (permalink) Old Aug 2nd, 02, 07:46 AM Thread Starter
Senior Tech
 
Join Date: Oct 2000
Location: CT
Posts: 389
Ahhh... Very good points!!!

I totally forgot about the curing!!! (Too much info going in my head!)

I'll look for the Duplicolor.

Thanks again,
Rob
RFrenette is offline  
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Team Camaro Tech forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address.
NOTE we receive a lot of registrations with bad email addresses. IF you do not receive your confirmation email you will not be able to post. contact support and we will try and help.
Be sure you enter a valid email address and check your spam folder as well.



Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may not post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome