Team Camaro Tech banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-16 of 16 Results
  1. My '68 sitting with my Brothers TT Viper

    Just a picture from the early days of my owning the Camaro (if you look closely you can see it had a mirror blue wrap on the front, that was the first thing I took off!) The Viper is my brothers twin turbo 2000hp Street Car!
  2. New Member Introductions
    I am new to the forum. I was researching low oil pressure at idle problems and came across a thread from here that covered what I was looking for so I figured I would join. I have owned my '68 Camaro for about a year now and I feel like there is A LOT that I don't know about these cars as simple...
  3. Engine
    I just completed a T56 conversion from a 400 auto in my 69 Camaro. The engine is a professional build 383 approx 2 years old. Prior to the trans swap there were no visible oil leaks (no drops on the garage floor, etc) and a very clean engine. Took me a month to finish the new t56 setup, but...
  4. Engine
    Motor is almost done, good or bad here it is: Would like to hear peoples opinions and any hp or torque estimates would be nice: 383 5.7 Eagle rods Dished hyper pistons 12 cc, zero decked block.039 compressed gasket, should be about 10.25:1 compression with 64cc heads Canfield aluminum...
  5. Engine
    Hey all, I bought a Blueprint 383 crate motor with roller rockers back in Feb. 2015 and have put about 4k on it so far. It's a great motor, makes lots of power and has a great sound. I have two small issues with it so far: 1. The oil pressure runs high, 85 psi, and if I give it a little gas...
  6. Member Classifieds
    I know this is pretty early, but in late November/early December my 383 in my '67 will be for sale. The reason I'm selling it is because I'm getting a big block and the reason for the delay in selling it is because I'm currently deployed. Once I get back the motor will be pulled and it will be...
  7. New Member Introductions
    Hello, I have owned a 67 Camaro since I was 16. I fell in love with the car the first time my friend kevin and I snuck out his dads 67 Camaro when we were 16. I am 47 now and have owned 6 1967 Camaro's. I have 2 RS/SS at this time. I own a red numbers matching 1967 with the following...
  8. Engine
    Looking for some advice, I have a 68 RS, with a 383 stroker. Car ran like a champ until I changed out the intake Manifold. I upgraded to an Edelbrok performer air gap manifold recently and I havent been able to get it to start since. I have verified all the usual suspects, 7 PSI of fuel, Air...
  9. Performance
    I have a 89 Rs, mild sub frame, iv got a 350 I built in highschool in it and wanna build a 383, I have a 350 bolck out of a 72 blazer, iv got it bored .30 over and lost direction on where to go from there, I want between 400-450 hp, and still be able to run 92 pump gas. Iv done research an wanna...
  10. Engine
    Looking for some advice, I have a 1968 RS with stock rear end, and stock 4 Speed manual transmission. I am rebuilding the motor and am building a 383 stroker from the original block. This is what I have so far: 350 bored +40 over Scat rotating assembly 92000BE 5.7" Rods 3.75" stroke 383 CI...
  11. Member Classifieds
    I couldnt find my other post so... My 1990 IROC-Z is still for sale and Ill get a pic of the RPO codes in a bit. Car is in need of some TLC from sitting in storage for couple of years. I replaced the fuel pump and it started right up and runs GREAT!! If you charge the A/C it will probably blow...
  12. Engine
    I am looking to replace the enging in my '80 Z28. I had the tranny replaced a while back spec'd out to handle ~500HP. These are 2 local engines for sale. Neither have been started and one is 1/2 price of other, but it would leave bit of cash to upgrade down the road. 1. I hear that 882's...
  13. Engine
    hey everyone, i have a 1975 Camaro with a 327 in it, i want to rebuild it because it has a loud knock in the engine. thinking maybe a cracked piston?...anyways i was wondering how i could rebuild it into maybe a 383 or something. i don't really know much about engines but am hoping to learn...
  14. Performance
    Hey Gents Im building a 383 with 10.5-ish CR with AFR 195 Eliminator heads and Im running XE282HR from Comp. Im unsure as to which intake, a Performer RPM or a weiand maybe? Ill have a T56 6spd and 3.73's. Ive looked into AED and Quickfuel carbs. I have a Holley 650Vac. sec. on the shelf and a...
  15. Member Classifieds
    Call it...creative acquistioning.l:)Cleaned out a building for the parts and need to get rid of some cams. ALL new some come with lifters. Flat tappet, Retro-fit SBC, BBC just email me. Some flat tappet kits are $90:yes: and that includes lifters!!:hurray: Some Retro-fit are $239. I think thats...
  16. Engine
    Hey Guys, I need your help again. I am sure this has been answered before, but i couldn't find the info i was looking for. I am building a 383 stroker and i don't know what damper to use. This motor will be in a 68 Camaro, 4-speed, 373 gears im pretty sure. It will be a street car with a few...
1-16 of 16 Results
Top