Team Camaro Tech banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 32 Results
  1. Transmission & Driveline
    Hey everybody, Just have a general question, I just purchased a 2011 Camaro LT V6 and I feel the clutch slipping. Everything is stock and was looking for a good clutch to replace for regular street drivability. I am caught between 2 clutches that both are around the same price ranges of about...
  2. Member Classifieds
    PRICE DROP!!! purchased new in 2013 3500 miles on this set up. absolutely nothing wrong with it . Just changed my mind and went with an automatic. american powertrain T56 6 speed hydraulic throw bearing master/slave cylinder LS flywheel LS bellhousing 10 inch american powertrain clutch...
    $3,750 USD
  3. Engine
    my 68 camaro LSx (no carb).. has been running fine for a while. Drove the car recently after being garaged for 2 weeks+, on my first drive, car ran fine no issues. On my way back, I've noticed a huge drop in RPM as I'm coming to a stop with the clutch pressed in, and suddenly stalls (shuts off)...
  4. Engine
    Hey all, I am brand new to the site and a lot of what I see so far is over my head! I have a 1967 hard top that I am getting quotes on to have transported from Indiana here to Charlotte. I recently had a 350 crate engine put in and my brother put it in, but said I needed to have someone look at...
  5. Transmission & Driveline
    Hello, I have a 5.3L Gen3 LS engine and a Tremec T56 and running into a problem that I'm hoping someone can shed some light on. When I measure my fully collapsed slave cylinder to the transmission mounting surface I get 1.935”. Looking at other people results this seems reasonable. However...
  6. Transmission & Driveline
    Hey first time rebuilding a car and I'm in the final stretch with fluids but I'm having trouble with my clutch I replaced it with a performance master cylinder and had to empty the whole system. Now that it's on the car in having trouble filling it with brake fluid. Anyone know if my system of...
  7. Transmission & Driveline
    I need a 621 bellhousing for my 69 SS restoration in which I am finally getting to the drivetrain stage. Pretty exciting! Does anyone have any experience with the Southwest Speed brand of bellhousings? They are pretty widely sold across the internet including some restoration parts stores...
  8. Transmission & Driveline
    Hey guys, I have a 67' with a TKO600 and mechanical clutch. Every now and again, mostly at low speeds *I think* the transmission/clutch makes this God-awful "vibraty" noise, almost like a grinding, and when I move the shifter around it goes away. It doesn't happen in neutral, it only happens in...
  9. Brakes, Suspension & Steering
    Clutch pedal sits couple inches lower than brake. I can pull it up by hand to make it even but it falls back down on its own. Doesnt seem right??
  10. Engine
    Hi everyone, A few years back I had a problem of when I would accelerate, the whole car would shake pretty violently. Subsequently my transmisson blew and it sat for a while. I recently put in a new transmission (M22W) and a new clutch disc (Centerforce Dual Friction). When I take off...
  11. Transmission & Driveline
    Okay, I've just mated my Muncie 4 speed to my 396 (both original to car) I had my engine professionally rebuilt so I started by purchasing a pilot bushing. After trips to 3 parts stores, I found a non-magnetic bronze bushing at NAPA and installed it using a block of wood between it & the hammer...
  12. Transmission & Driveline
    Does anyone have the clutch return spring for an L48 350/300hp manual actually attached to the factory mount point - whatever that is/was. :D The Aim is so nondescript I'm just scratching my head. A picture of a factory setup might be nice but I couldn't find a single one here or at CRG. If...
  13. Transmission & Driveline
    Hi all - I'm chasing down a noise coming from front of trans in my '69. Shifts perfectly at all times. Around town = perfect. Swapped in hyd clutch set-up with no change in noise at speed. It seems to make same noise above 70mph in ALL conditions: under load, in neutral, coasting 70mph with...
  14. Transmission & Driveline
    It's pricey, but thinking about using one of the McLeod Hydraulic Clutch Conversion kits on my 69 Big Block Camaro... Anyone have any experience with the installation? 1434002 - Master Cylinder Firewall Kit - $329.95 1301 - Bearing/Slave Cylinder Assembly - $446.00
  15. Fourth Generation
    i just installed a brand new clutch today and when i got everything done i went to drive it. i put the car in reverse and without giving it any gas i slowly let the clutch pedal out and there were a lot of vibrations coming from what felt like the transmission/driveshaft area. this also happened...
  16. Fourth Generation
    i just bought this camaro and i am not to savy on hydro clutches my problem is my clutch does not start engaging until about 3 in from the top and in 5 & 6 it slipps at half to full throttle. please any info will help thanks
  17. Transmission & Driveline
    69 Camaro BB... replacing some worn clutch linkage items and noticed the rubber seal on the block side pivot ball is stretched and distorted... The ball stud is fine, but I'm having a hard time finding just the rubber seal. Anyone where I can pick one up?
  18. Transmission & Driveline
    Hi Guys I just had my clutch replaced with a new centerforce dual friction clutch, flywheel, throw out bearing and clutch fork. The mechanic gave me the car back saying i needed to repllace the clutch return spring because wat was fitted wasnt correct and caused issues with the movvement of the...
  19. Transmission & Driveline
    Hi i have a stock 69Z i need help choosing between 2 clutches from CENTERFORCE [ centerforce II or duel friction ] is one better than the other and what is the difference, i dont want a hard pedal pressure thanks TC
  20. Engine
    Recently when changing from a power glide to a 700R4 I needed a flywheel turner. No fun buying one, more satisfaction from making one, here is what I came up with for $4.00 and it works great. Just thought I would share in case anyone had an interest. Purchase a 8" or 9" gate hinge from your...
1-20 of 32 Results
Top