Team Camaro Tech banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-11 of 12 Results
  1. LSx Swap
    Hello All, Perhaps this is a newbie question but I can’t find the answer on a internet search so I need to ask. I have an LS1 with a build up bottom end. I am wishing to put some aftermarket heads on it (probably AFR). My question is the bolt pattern the same as the factory heads for the...
  2. General Camaro Tech Discussions
    Gentlemen, I have a 68 Camaro SS 396 with an Edelbrock 1406 600 CFM. Can anyone tell me how to adjust one. My car runs great when I get on it, but cruising down the highway it sputters and spits and backfires occasionally. I was told to turn the two adjusting screws on the front of the...
  3. Engine
    Afternoon Guys 'n Gals - So I've put this in the engine section because I'm not convinced this is related to my brakes. I'll explain why: Brakes have previously performed OK, not perfect but OK, I could lock the wheels up with a good stomp or a bit of a pump pump stomp. I had issues with the...
  4. Engine
    Hey guys. I'm going through the motions trying to get my carb optimally done up as best I can, and have a few questions. First off, here's what I've got as far as the motor goes; - 355 sbc - Comp cams 276-tl56 - Edelbrock Performer RPM intake manifold - 3947041 cast iron heads (I've heard...
  5. Engine
    Hi, new member! Car has a 350 – auto, lightly modified. Car will idle for roughly 5 minutes, then just dies, doesn't bog down, no change in rpm, just quits. Last time car was driven (about a week ago), ran and drove fine for 2 minutes, died and backfired when attempting to restart. That's...
  6. Engine
    Hey everyone: My father and I figured the winter would be a good time to begin building the motor for our '69 project. It's not going to be a track car, but we do want it to have some go, and will have a TH400 and 12-bolt with 3.73's behind it. We don't have much experience with blueprinting...
  7. Engine
    I am currently trying to get my 68'RS running properly and I need a new carb but I'm not sure where to start. I currently have an old Carter 625cfm clone and I don't think trying to refurbish it would be worth it. I also looked at the 650 Rochester Quatrajet and have heard a lot of people say...
  8. Performance
    I have a 69 camaro and a 350 engine all stock and a 4 barrel quadrajet carb. A friend gave me an Edelbrock torker II intake manifold but I don't know if I should put it on or if I am better off with the original intake manifold. I don't plan to change the carb anytime soon. Also, another...
  9. Engine
    ok... so i have a thirdgen camaro... It has a 383 stroker, 10:1 comp. mild cam ( 512 lift i think) Edelbrock Performer RPM intake, headers, and an edelbrock 750 cfm carb. As far as i know there is no in tank pump, i have a high perf. holley mechanical fuel pump that is pretty new. The fuel...
  10. Vendor Spotlight! Great Deals for Members
    Save $$$ on Edelbrock / Musi Aluminum Big Block Chevy Cylinder Heads. All heads are sold individually. Assembled Sale Priced @ $1,849.99 shipped ($150.00 Savings) http://cs3automotive.com/index.php?a=PROD:394 Bare Sale Priced @ $1,449.99 shipped ($50.00 Savings)...
  11. Vendor Spotlight! Great Deals for Members
    I have some Edelbrock Carburetors on sale. Edelbrock Thunder Series p/n 1806 - 650 CFM; Electric Choke - 349.99 shipped http://www.cs3automotive.com/index.php?a=PROD:446 p/n 18064 - 650 CFM; Electric Choke; Endurashine - 429.99 shipped http://www.cs3automotive.com/index.php?a=PROD:1616...
1-11 of 12 Results
Top