Team Camaro Tech banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-13 of 14 Results
  1. Member Classifieds
    First come, first served. Free to the needy LOL... a complete set of brand-new, never used Vintage Air Hard Lines for a 1969 Camaro. This was part of my BBC kit, I think it'd all work with a SBC or BBC where the compressor is on the Driver's Side. All you do is pay for the ride. PayPal is OK or...
    $0 USD
  2. Member Classifieds
    Wrong number posted.
  3. Engine
    Hey guys. I'm going through the motions trying to get my carb optimally done up as best I can, and have a few questions. First off, here's what I've got as far as the motor goes; - 355 sbc - Comp cams 276-tl56 - Edelbrock Performer RPM intake manifold - 3947041 cast iron heads (I've heard...
  4. Engine
    Motor is almost done, good or bad here it is: Would like to hear peoples opinions and any hp or torque estimates would be nice: 383 5.7 Eagle rods Dished hyper pistons 12 cc, zero decked block.039 compressed gasket, should be about 10.25:1 compression with 64cc heads Canfield aluminum...
  5. Engine
    Hello all, I have a 1968 camaro RS with a 350 I built and have had on the road for about 2 years now. The car used to run like crap, but fixed that issue by increasing the jet size from 65/68 to 69/73. Now the car runs much better, but still has two small problems. The first is a problem at...
  6. Engine
    Dear Camaro lovers, I'm a guy from Norway, (therefore un-steady and bad English) I have a 1972 Camaro, I have built my one engine, a 383 stoker. From the first day I started up and breaked in the engine, I have had the same annoying (!) ticking sound. I bought a complete set from...
  7. Member Classifieds
    New Edelbrock 7102 Performer RPM Cam & Lifter Kit: Performer RPM Camshaft Kit 1957-86 Chevy 283-400 .488''/.510'' Lift 308°/318° Adv. Duration 1500-6500 RPM Range This cam lists for $185.00 + shipping from Jegs. $150.00 + $20.00 shipping to lower US.
  8. Member Classifieds
    I couldnt find my other post so... My 1990 IROC-Z is still for sale and Ill get a pic of the RPO codes in a bit. Car is in need of some TLC from sitting in storage for couple of years. I replaced the fuel pump and it started right up and runs GREAT!! If you charge the A/C it will probably blow...
  9. Member Classifieds
    Im putting a LS1 in my Camaro so Im selling my EFI system. This is the narrow band version. I had it in my car for some time but never really got a chance to put a lot of miles on it. Im going to say less than 100 miles. I am going to include a electronic distributor that will allow the...
  10. Engine
    I'm getting a 400 sbc built for my 68 camaro, got every thing ordered to match as close to one and other as possible cam to heads heads to intake carb pistons to crank, etc. So a couple of days ago the machine shop got all the parts in and went on to balance the engine but to there and my...
  11. Engine
    I have a 302 with four speed in my 69 camaro with 4.10 gear and was wondering whats the best times you guys have gone? i've been to the track, but mine wasn't tuned and was bogging down bad on take off and ran a 13.4 et. i've switched the carb to a new one that doesn't have a dead spot in it and...
  12. Member Classifieds
    Call it...creative acquistioning.l:)Cleaned out a building for the parts and need to get rid of some cams. ALL new some come with lifters. Flat tappet, Retro-fit SBC, BBC just email me. Some flat tappet kits are $90:yes: and that includes lifters!!:hurray: Some Retro-fit are $239. I think thats...
  13. Performance
    hello fellow TC'ers. Ive seemed to of stumbled upon another lrg jrnl 327, im still a lil wet behind the ears in the motor aspect of the car world.But it hasnt slowed me from having my fun,Im wondering what kind of cam you guys could recommend me.As is, i only plan to bore and install Forged...
1-13 of 14 Results
Top