Team Camaro Tech banner
wiring
1-20 of 46 Results
  1. New Member Introductions
    Okay Folks, Our Infinitybox team is proud to join the Camaros.net community. We're a team of engineers with a history of designing wiring harnesses and electronics control modules for the OEM's and the off-highway vehicle market. In 2009, we had a chance to break off on our own to design...
  2. Electrical & Wiring
    Hello. I own a Gen 4 Camaro Z28 (1996 body on 1995 Z28 motor, suspension, everything... Including wiring). Which leads me to my issue, I finally got the car running and i drove it to a gas station where i preceded to fill the tank completely. But when i went to start the car again the car turned...
  3. Fourth Generation
    Hello! About a month ago I started swapping a LT1 out of a 1995 camaro into a V6 1996 camaro body. Yesterday I finished swapping every harness into the new body due to some changes that happened in 1996 with the inclusion of a BCM module. So I swapped the whole body harness into the car with all...
  4. Electrical & Wiring
    So I am a little OCD when it comes to wiring, one of the first things I do when I pick up a car is clean it up. I am forever searching for grommets the right size to fit holes in the fire wall, to fix where previous owners leave me wires chafing against sheet metal. I decided this round I...
  5. Electrical & Wiring
    Hi everyone, So I recently rebuilt my engine and in the process upgraded my points distributor to an HEI, and my factory starter to a mini starter. The factory starter had 3 terminals (Battery+, S, R), and the new starter has 2 terminals (Battery+, S). Based on the instructions and what I read...
  6. Convertibles
    Need some help. I have replaced the power top switch twice, keeps burning out, only on the up side. Does anyone have any insight as to wiring a relay into this to help eliminate this issue? The switches get expensive at $40 a pop. I am relative new at this, so pics or insight into specifics...
  7. Electrical & Wiring
    Where can one get clips that you would use to attach wires to the chassis of the car that go into factory holes, i.e. wire running to dome light or running over front fenderwells/radiator support? Finishing up my five-year project, whew... Thanks.
  8. Electrical & Wiring
    I'm about to start wiring my 69 RS/SS after a frame-off restoration. I am adding Vintage A/C under dash. My question is whether anyone has any recommendations for anything I should do before or while I am doing the wiring or assemble the dash. Right now the car body is completed but otherwise...
  9. Electrical & Wiring
    Hi All, I am troubleshooting a charging issue with my 69Z.I have to admit this is intimidating for me, I hate dealing with wiring issues... Anyway, I am getting 0V out of the alternator, I have replace the VR and even tried Jumping the Red and Brown wire at the VR and still nothing. I had the...
  10. Fourth Generation
    I need help with my car. I know it's hard to diagnose without seeing it, but here goes. I've got a 1992 Chevy Camaro RS, 3.1L V6 in it, about 190k mi now. Anyways, a few months ago, the tachometer was jumping around pretty violently. My car would stall, die randomly, then not even start. My...
  11. Electrical & Wiring
    Hello everyone- I am having trouble with my tach. It works, but it is giving a high reading and when I give it gas it really jumps high. I put an analog tach to it at the same time. The analog reads 800 and the factory tach reads 1500. I recently had it services at Redline- good guy. It seemed...
  12. Electrical & Wiring
    How do you access the brake light switch for rear lights? Do you have to remove instrument gauges? I'm assuming that the switch is my problem. turn signals, emergency flashers, running lights all work fine. Any suggestions would be really appreciated!
  13. Electrical & Wiring
    My '67 Camaro has a 350 87-88 model engine. I have an electronic ignition. I'm only getting 11.92 volts to the distributor. Would this cause my engine to run rich? I've tried three different carbureters and I still have the problem of running rich. A friend said that I may not be getting...
  14. Fourth Generation
    I am in the process of replacing the power window on my Passenger side. When I bought it though it didnt have a motor in it, just the window being held up by two wires. Go figure. Any I was using my driver side as a reference as to where to mount it to the door when the wind blew my window shut...
  15. Electrical & Wiring
    So i have a thread already about my situation (http://www.camaros.net/forums/showthread.php?t=198871 ). I have a good 68 harness (lights and engine) but the plugs to the firewall are not the same for my 67. I have the wires all mapped out, if I can get ahold of some plugs from a 67 it would be...
  16. Electrical & Wiring
    does anyone have a diagram of how the ignition is supposed to be wired?
  17. Electrical & Wiring
    I picked up a wiring harness along with some other goodies today, however, it's from a 68 and mine's a 67. At first I thought it should be the same but after looking it seems that the sockets are different. Any way I could make it work?
  18. Electrical & Wiring
    Hello fellow members. As I am a new member, I am not new to viewing these very informative threads. I am working out the kinks in my 67 rs/ss, and I am at a brick wall of sorts. I have all new wiring harnesses under the dash, new front lighting wiring harness, new limiting switches, and new...
  19. American Auto Wire
    In this video series that coincided with the release of our 1959-1960 Impala Classic Update kit, Don Bock chronicles the installation of the kit in a 1960 Bel Air. The fifth episode premiered Monday, check them all out! In other news, American Autowire recently released our new 1970 Mustang...
1-20 of 46 Results
Top