[R66]

Don't have a pair, but I have one I saved, can't remember which side. I will look about Tuesday if you still need one. Have to bury a very close friend tomorrow - long day. I bet him he would outlive me. Guess I lost.
If you find both sides it would save shipping. Check and see if a Nova doesn't use the same spindles.

 

[patman2]

Oof…my condolences on your loss…

TBH…I don’t remember which side had the damage, so I’m looking for both. I’m planning on doing the control arm bushings, so I figure it’s time to fix the spindle.

 

[R66]

With all of the disc brake conversions, you should be able to find a good pair fairly reasonably and closer to home to save shipping.

 

[fairfax1000]

Oof…my condolences on your loss…

TBH…I don’t remember which side had the damage, so I’m looking for both. I’m planning on doing the control arm bushings, so I figure it’s time to fix the spindle.

Email Mark

 

[Georgia68]

I did disc brakes. I will look and see if mine are still around. I scrapped a lot of the old parts. Will let you know later today.

 

[timkeller]

I have a pair. Did a disc swap and don't need. I'm in Kitchener Ontario Canada. I'm not sure what shipping would be to you.

 

[patman2]

With all of the disc brake conversions, you should be able to find a good pair fairly reasonably and closer to home to save shipping.

Exactly. Fingers crossed!!!

Email Mark

Thanks, will keep that in mind...

I did disc brakes. I will look and see if mine are still around. I scrapped a lot of the old parts. Will let you know later today.

Thank you!

I have a pair. Did a disc swap and don't need. I'm in Kitchener Ontario Canada. I'm not sure what shipping would be to you.

I'm in the NH lakes region. Ya, shipping might be an issue. Thanks, but let me see if a domestic source works out first.

 

[fairfax1000]

Exactly. Fingers crossed!!!



Thanks, will keep that in mind...



Thank you!



I'm in the NH lakes region. Ya, shipping might be an issue. Thanks, but let me see if a domestic source works out first.

Postal service priority box. $25 or so I would think.

 

[57vette]

Pat... I will check my parts shed and see if I have a set still around from when I did the conversion. Pretty sure I have some of the parts. Massachusetts to New Hampshire shouldn't be too bad, I'll get back to you later today once I get home.

 

[fairfax1000]

Pat... I will check my parts shed and see if I have a set still around from when I did the conversion. Pretty sure I have some of the parts. Massachusetts to New Hampshire shouldn't be too bad, I'll get back to you later today once I get home.

The big Post office priority bulk rate box will hold them. I used one last week….was $21.50 or so.

 

[patman2]

Yes, USPS priority is the way to go...domestically. Not sure what the story is from Canada though, so trying to keep it simple.

Thanks all!!!

 

[X-77 keith]

Nova is the same as well.👍

 

[scblucam]

I spotted some damage on the spindle where the bearing rides last time I had it apart. Most likely there was a wheel bearing failure sometime in the past. I replaced the bearing, and it has been ok, but I’d feel better with an undamaged spindle. Anyone have a pair of stock drum spindles they’d like to sell?
Thx!!

I have a set but they got wet so I don't know the condition. Probably surface rust. Need to look tomorrow, too dark now.

 

[fairfax1000]

I have a set but they got wet so I don't know the condition. Probably surface rust. Need to look tomorrow, too dark now.

#Rustoleum

 

[patman2]

I was pretty sure it was the left (driver’s) side, and I finally got around to pulling the hub. The outer bearing area looks like a bearing spun on it in the past. Correct?

Anyway…still looking for a replacement for at least the left side.

 

[fairfax1000]

I was pretty sure it was the left (driver’s) side, and I finally got around to pulling the hub. The outer bearing area looks like a bearing spun on it in the past. Correct?

Anyway…still looking for a replacement for at least the left side.

View attachment 307742

Did he not respond?

 

[scblucam]

I still have a set but can't access them right now due to illness. Can't safely walk where they are. Going to ER when wife gets here.

 

[ryeguy2006a]

I have a pair and also have a pair of drums hubs.

 

[Georgia68]

Being there are many offers of spindles posted, I was waiting for OP to ask a specific member to send photos of their spindles. No sense pullng my spindles out of the bin in the container, if there's no possibility of them being shipped. Still waiting for him to ask someone.